Network Address Translation (NAT) is a technique that allows multiple devices to share a single public IP address. NAT is commonly used in home and office networks to allow the devices on a private network to access the internet through a single public IP address.

Masquerading, on the other hand, as the name suggests, hides your identity behind a mask or another presumed identity. Just like that, in the world of computer networking, one type of network address translation is called masquerading which is used to hide the identity of the devices on the private network by replacing their IP addresses with the IP address of the router or gateway device.

When a device on a private network wants to communicate with a device on the internet, it sends a packet to the gateway device on the private network which then forwards the packet to the internet. However, the source IP address of the packet is the private IP address of the device which is not valid on the internet. To solve this problem, the gateway device replaces the source IP address of the packet with its own public IP address so that the device on the internet sees the packet as coming from the gateway device, rather than from the private device.

Implementing Masquerading with Iptables

To implement masquerading with iptables, we need to add a rule to one of the routing chains of the NAT table. The postrouting chain is used to modify the packets that are leaving the system, after they have been routed.

Step 1: Adding a Masquerading Rule to the POSTROUTING Chain

Run the following command in the Linux terminal:

 
This command adds a rule to the POSTROUTING chain of the NAT table which matches all the outgoing packets that are going through the eth0 interface, and replaces their source IP address with the IP address of the eth0 interface.

• • The -t option is used to specify the table that we want to work with which, in this case, is the NAT table.
  • The -A option is used to add a new rule to the chain.
  • The -o option is used to specify the outgoing interface that the packets are going through.
  • The -j option is used to specify the target of the rule which, in this case, is MASQUERADE which means that the source IP address of the packet should be masqueraded.

Once this rule is added, any outgoing packet that is going through the eth0 interface has their source IP address masqueraded with the IP address of the eth0 interface.

Step 2: Specifying an IP Address to Masquerade

By default, the masquerading rule applies to all outgoing packets on all interfaces. However, it is possible to specify a specific interface to masquerade using the -s option followed by the IP address of the interface.

Run the following command:

 
Note: This applies the masquerading rule only to packets that are going out through the eth1 interface.

Step 3: Specifying the Source IP Address to Masquerade

The masquerading rule replaces the source IP address of all outgoing packets with the IP address of the outgoing interface by default.

Run the following command to specify a different source IP address to use using the –to-source option followed by the IP address:

 
Note: This command masquerades all outgoing packets with the IP address 203.0.113.1.

Step 4: Specifying a Destination Address Range to Exclude from Masquerading

Sometimes, it may be necessary to exclude a range of destination IP addresses from the masquerading rule.

This can be done by adding a rule to the PREROUTING chain that matches the packets with the excluded destination addresses and sets a special mark on them. A masquerading rule in the POSTROUTING chain can be configured to skip the packets with that mark.

Run the following command to exclude the IP address range 203.0.113.0/24 from masquerading:

 
These are just a few examples of the many options that can be used to customize the behavior of masquerading with iptables. With the flexibility that is provided by iptables, it is possible to implement the complex networking configurations and security policies on a Linux system.

Conclusion

In this article, we explored what masquerading is and how to implement it with iptables. Masquerading is a useful technique to hide the identity of devices on a private network, and iptables provides a simple and flexible way to implement it on a Linux system. By adding a masquerading rule to the POSTROUTING chain of the NAT table, we can ensure that all outgoing packets from the devices on the private network have their source IP address masqueraded with the IP address of the gateway device so that they can communicate with the devices on the internet without revealing their true identity.